nylon syringe filter

The Nylon Syringe Filter produced by Aijiren is mostly used for reagent filtration or sample preparation. Nylon Syringe Filter has different specifications. The filter membrane diameter is 13mm, 25mm and 33mm, which can be selected according to the capacity of the sample. Aijiren provides 0.22μm and 0.45. Two μm specifications are convenient for customers to choose. The Nylon Syringe Filter produced by Aijiren meets customers’ requirements and needs for product preparation.

The Syring Filter with nylon membrane produced by Aijiren has good hydrophilicity, acid and alkali resistance, and oxidation resistance. It is not only suitable for aqueous solutions containing acids and alkalis, but also for organic solvents such as alcohols, hydrocarbons, lipids, phenols, ketones and other organic solvents. It can be used for organic solvents such as strong acid, 70% ethanol, dichloromethane and so on. High temperature resistance, good strength, stable chemical properties.

Aijiren’s syringe filters with nylon membranes are compatible with a wide range of solvents, making them ideal for fast filtration of most aqueous and organic solutions. Therefore, when a mixture of sample aqueous solution and organic solvent passes through nylon membrane, fine droplets of extractor solvent accumulate and are separated from the sample aqueous solution. Using this simple method, the total extraction time is only 3-4 minutes; It is environmentally friendly, has no centrifugal effect, provides a higher sample purification rate by filtering receptor phases, and filtering reagents ensures reduced impurities and protects the color column.

Nylon Syringe Filter material: high-density polypropylene PP for exterior wall; filter membrane: nylon. Filter area: §¶13mm-0.65cm2, §¶25mm-3.9cm2. Inlet pressure: §¶13mm-7bar, §¶25mm-5bar [1 bar (bar) = 100,000 Pa (Pa) = 10 Newton/square centimeter as the pressure unit] Temperature: 60-130 degrees Celsius. Features: Significantly hydrophilic, no need for pre-wetting. The pore size is uniform, and it has strong elasticity and adsorption force, which can ensure effective retention and meet the application requirements of fine filtration. It has good chemical compatibility, is compatible with most reagents, and does not shed fibers. It meets the standards of the pharmaceutical industry.

And the nylon membrane syringe filter produced by Aijiren can be used for alkaline blotting and fixation. If fixing methods such as baking and ultraviolet light are used, higher nucleic acid detection sensitivity can be obtained. Since the nylon membrane is a hydrophilic membrane, it does not need to be immersed in a solution such as ethanol or methanol for activation. The nylon syringe filter produced by Aijiren is only for professionals to use for scientific research, not for food.

Aijiren’s syringe filter with nylon membrane is compatible with a variety of solvents and is very suitable for rapid filtration of most aqueous and organic solutions. Therefore, when the mixture of the sample aqueous solution and the organic solvent passes through the membrane, the fine droplets of the extraction solvent gather and separate from the sample aqueous solution. The nilong syringe filter produced by Aijiren is environmentally friendly and has no centrifugal effect. By filtering the receptor phase, it can provide a higher sample purification rate.

As an important tool for filtering reagents, the Nylon syringe filter plays a very important role, especially in chromatographic consumables. A slightly larger impurity particle in the reagent may cause clogging of the instrument.

The nylon membrane used in the syringe filter has high mechanical strength, chemical stability, can be tolerated by most organic solvents, has very low extractables, has good thermal stability and natural hydrophilicity, and is filtered by most aqueous solutions characteristic.

Nylon membrane has high strong mechanical strength, chemical stability, can be tolerated by most organic solvents, extremely low in extractables, good thermal stability (up to 50¡ãC), natural hydrophilic and the majority of water solution filter characteristics. It more often applied to the common organic solvent HPLC mobile phase filtering.

Nylon has excellent flow characteristics, extremely low extractable level and mechanical stability, and can provide the best combination of physical parameters to meet the most stringent analysis requirements of 13mm, 25mm and 33mm diameters. Nylon’s natural hydrophilicity, high protein binding capacity and high dirt adsorption capacity are natural advantages.

In addition to HPLC, syringe filters have a multitude of other applications. A syringe filter adds a few minutes and a minimal expense to your testing process, but you will see a big return on your investment. Small volume venting£¬HPLC sample preparation£¬Removal of protein precipitates£¬Routine QC analysis£¬Dissolution testing.

Polyethersulfone filter has the characteristics of high flow rate, low extraction loss, and higher mechanical resistance than cellulose membrane. It is suitable for biological, pharmaceutical, sterilization and filtration. The membrane is sealed in the polymer shell without using any adhesive. Each unit is ETO or gamma ray sterilized and guaranteed to be pyrogene-free.

The advantages of nylon: 1. Toughness 2. Wear resistance 3. Smoothness 4. Light weight 5. Insect resistance 6. Anti-mold and the material is not easy to generate static electricity, deformation, pilling and ageing.

Product applications: water purification, HPLC sample preparation, mobile phase solution filtration, cell culture, microbial filtration or sampling, protein precipitate removal, particle removal and monitoring, QC analysis, content consistency, dissolution testing, environmental sampling, food analysis. Generally speaking, 0.45 ¦Ìm pore size is suitable for removing particles from samples or the mobile phase solution of chromatography equipment, and 0.22 ¦Ìm is suitable for filtering microorganisms.

Membrane separation technology is hailed as “one of the most promising high-tech developments in the middle of the 21st century”. Among them, microporous membrane separation is the most eye-catching application in the fields of biology, chemical analysis and pharmaceuticals. There is no need to change the membrane and clean the filter, save the complicated and time-consuming preparation work, and is widely used in the laboratory.

This nylon membrane can be used for alkaline blotting and fixation, but if fixing methods such as baking and ultraviolet rays are used, higher nucleic acid detection sensitivity can be obtained. Since the nylon membrane is a hydrophilic membrane, it does not need to be immersed in ethanol, methanol and other solutions for activation. This product is only for scientific research by professionals, and must not be used for clinical diagnosis or treatment, or used for food or medicine, and must not be stored in ordinary residences. For your safety and health, please wear lab coats and disposable gloves for operation.

1. The pore size of the needle-punched membrane is accurate, providing comprehensive protection for your instrument and chromatographic column
2. There is a clear label on the Nylon syringe filter to avoid confusion
3. The luer interface of the needle filter with lock can prevent the filter from flying out due to excessive pressure

Membrane: HPLC Certified Nylon
Use with: Bases, Most HPLC solvents, Alcohols, Aromatic Hydrocarbons, THF.
Don¡¯t use with: Acids, Aggressive Halogenated hydrocarbons, protein samples (Nylon is a high binder)
Sterilization: Syringe filters can be sterilized by autoclave at 125¡ã for 15 minutes.
Applications: General Laboratory filtration, most HPLC samples

Instructions for use and precautions:
1. It must be used with disposable syringes and glass syringes. The interface is standard. Put the needle filter on the syringe first, then pour the liquid into the syringe, press the push rod down, and collect the filtered liquid.
2. Do not use a syringe smaller than 10cc, because the small-volume column may cause the pressure to exceed the upper limit and cause damage to the filter membrane.
3. Only for laboratory use, one-time use, non-renewable.
4. The filtrate at the beginning of the part should be discarded. The volume is about the dead volume of the filter. Taking 25mm as an example, discard the first 1mL filtrate; or pre-clean the filter with 1 to 2mL of solution.

Aijiren syringe filter membrane use method introduction: before inhaling the sample, suck about 1ml of air into the syringe, so as to minimize the liquid residue, suck the sample into the syringe, invert the syringe and clear all the residues on the top Clean, connect the needle filter to the syringe, tighten it gently to ensure a good seal, filter the sample in the syringe and inject it into the sample bottle, and then follow the steps to maximize the recovery rate, remove the filter, and suck air into the syringe, Reconnect the filter head and eject all residual samples.

The nylon membrane of the syringe filter should be compatible with the chemical characteristics of the sample. The nylon membrane should be compatible with various water-based and organic solvents. The membrane should also have high resistance to HPLC solvents and chemicals. The 0.45mm aperture ensures that you have enough capacity and throughput to process samples efficiently and quickly.

Aijiren brand syringe filters are HPLC certified to ensure reliable and consistent results. Water, methanol, and acetonitrile are used for testing, and HPLC is used for detection at 210 and 254 nm wavelengths. None absorbs ultraviolet light, which can provide a purer analytical background.

Our Syringe Filters are high quality, well packaged and sold at a fair competitive price. They are available in most of the major membrane materials including Nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF which are supplied in 13mm, 17mm, 25mm and 30mm formats in virgin polypropylene housings.

Syringe filter is a quick, convenient and reliable filter tool used routinely in the laboratory.Because they don’t need to change the membrane and filter cleaning, it’s eliminating the complex and time-consuming preparation. It is widely used in the sample pre filtration, removal of particles, aseptic filtration of liquids and gases. It is the preferred method to filter small samples before loading into HPLC and GC ,and it is often used with disposable syringe.

A syringe filter (or wheel filter) is a single-use, membrane-based device used for the removal of particulate impurities from small (≤ 100 mL) liquid samples. Selected based upon the desired end application, disposable syringe filters are commonly used in labs for fast and efficient filtering, material purification, or even sterilization.

UHPLC Precolumn Filter
• Economical protection against microparticles.
• Extend UHPLC column lifetime.
• Negligible effect on column performance.
• Universal fit—easily connects directly to any brand column.
• Leak tight to 15,000 psi (1,034 bar).
• Does not contribute to system backpressure.
• Does not contribute to band broadening.

With PES syringe filter membrane mechanically strong character, it can handle high-temperature liquids, with great flow rate (better than PTFE), and low protein binding. With these features, PES syringe filters offer superior performance for use with biological samples and media culture. Workable pH range ~3-14.
Nylon: Nylon membrane filters are hydrophilic, flexible, tear-resistant, and autoclavable. They are resistant to a range of organic solvents and suitable for use with high pH samples. Nylon binds proteins. Unsuitable for acidic solutions. pH range ~3-14.
MCE (Mixed Cellulose Ester) syringe filters are an ideal choice when biological samples are involved. Mixed Cellulose is a hydrophilic membrane offering both low protein binding coefficients and exceptional flow rates.

Ideal for use with aqueous and organic solvents, Nylon Syringe Filters are an excellent choice for filtering high-performance liquid chromatography samples. Nylon syringe filters are durable, tear resistant and wet evenly.
PES (Polyethersulfone ) syringe filter is natural hydrophilic which makes is an ideal choice (highly recommended) for aqueous solutions and alcohols. It’s not necessary to treat the filter membrane surface with wetting agents.

Aijiren Tech’s syringe filters are a complete range of non-sterile disposable syringe filters for reliable sample preparation. Repeatable membrane quality and automated production processes ensure that particles are removed from each sample, extend the service life of the analytical column, and minimize damage to the inlet or valve.

The membrane materials produced by Aijiren are provided by the most famous people in the industry, and in the ISO9000 certified production process, under certified clean room conditions, the latest manufacturing technology is used to ensure high-quality and stable products to achieve the highest standards . All syringe filters are HPLC certified.

Our Syringe Filters are high quality, well packaged and sold at a fair competitive price. They are available in most of the major membrane materials including Nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF which are supplied in 13mm, 25mm formats in virgin polypropylene housings.

The syringe filter produced by Aijiren is the preferred method for filtering small samples before being loaded into HPLC and GC, and is usually used with disposable syringes to filter out impurities in the sample to ensure that there is no quality in the test Problems and affect the experimental results.

Aijiren syringe filter is a fast, convenient and reliable filter tool, usually used in the laboratory. Since they do not require membrane replacement and filter cleaning, complicated and time-consuming preparations are eliminated. It is widely used for sample prefiltration, particle removal, aseptic filtration of liquids and gases.

Aijiren Syringe Filter is a comprehensive range of non-sterile disposable syringe filters for reliable sample pre-treatment. Reproducible membrane quality and automated manufacturing processes ensure particles are removed from all samples, extending the life of analytical columns and minimizing injection port and valve damage. The Aijiren syringe filter is available in 0.22um and 0.45um porosity, 4, 13, 25 and 30mm diameters.

The Aijiren Tech Syringe Filter is a comprehensive non-sterile disposable syringe filter for reliable sample preparation. Reproducible membrane quality and automated manufacturing processes ensure particles are removed from all samples, extending the life of analytical columns and minimizing injection port and valve damage.

Membrane materials are supplied under the industry’s best names, and ISO9000 certified manufacturing uses the latest manufacturing technology to ensure high quality and consistent products, performed to the highest standards in certified cleanroom conditions. All syringe filters are HPLC certified.

Our syringe filters are high quality, packaged and sold at fair competitive prices. They are available in most of the major membrane materials including nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF, and are available in 13mm, 17mm, 25mm and 30mm formats for virgin polypropylene housings.

Syringe filters are a fast, convenient and reliable filter tool that is routinely used in laboratories. No need to replace membranes or clean filters, which eliminates the need for complex and time-consuming preparations. Widely used in pre-sample filtration, particle removal, and aseptic filtration of liquids and gases. This method is suitable for rinsing small samples before loading into HPLC and GC, and is often used in disposable syringes.