cod test tube

The 16mm COD Test Tube is a special glass tube designed for Chemical Oxygen Demand (COD) testing in the laboratory. It has a diameter of 16mm, providing ample space for sample collection and analysis. The tube is made of high quality glass, ensuring durability and chemical compatibility for accurate and reliable COD measurements.

The COD Test Tube produced by Aijiren is often used in chemical oxygen demand testers. Since the chemical oxygen demand test is a test that requires strong corrosive reagents, Aijiren uses the most inert and stable glass to produce the COD Test Tube, which is produced by Aijiren. COD Test Tube meets customer requirements for oxygen demand testing.

The COD tube provided by Aijiren uses high-quality glass, which is extremely inert and will not react with reagents. Through Aijiren COD tube test, the time required for the measurement process is greatly shortened, especially for standard analysis and series measurement, which greatly reduces the workload.

It is worth noting that if the used COD Tubetests contain strong sulfuric acid and other chemicals, the reagents must be handled carefully. The items in the pipeline should be disposed of in accordance with the requirements of local authorities. These tubes can only be used once and cannot be reused.

With the Aijiren COD tube test, each user can easily perform highly sensitive and accurate water detection. The time required for the measurement process is greatly shortened, especially for standard analysis and series measurement, while greatly reducing the workload.

The COD Test Tube produced by Aijiren has a capacity of 10ml, 12ml, and 15ml. The caliber is 16mm. It is often used for water quality testing and contains liquid reagents. It is mostly used in the petroleum industry and chemical analysis.

In this test a reagent blank is used instead of the usual water blank referred to in the general photometer operating instructions. The reagent blank is prepared by adding deionised or distilled water to the reagent tube and then digesting the tube in the same manner as for the water sample.
It is not necessary to prepare a reagent blank each time the test is carried out. The reagent blank tube may be prepared weekly and used repeatedly with all samples prepared from the same batch of reagent tubes. The reagent blank should be stored in the dark between uses.

Chemical oxygen demand is a vital test for assessing the quality of effluents and waste waters prior to discharge. The Chemical Oxygen Demand (COD) test predicts the oxygen requirement of the effluent and is used for monitoring and control of discharges, and for assessing treatment plant performance. The impact of an effluent or waste water discharge on the receiving water is predicted by its oxygen demand. This is because the removal of oxygen from the natural water reduces its ability to sustain aquatic life. The COD test is therefore performed as routine in laboratories of water utilities and industrial companies.

With the Aijiren COD tube test, each user can easily perform highly sensitive and accurate water detection.
The time required for the measurement process is significantly shortened, especially for standard analysis and series measurement, while significantly reducing the workload.
The COD Test tube contains a precise dose of reagent. Therefore, excessive chemical inventory is avoided and work safety is improved.

Details of Chemical Oxygen Demand Test:

2mL of a water or watse water sample are added to a 16mm glass culture tube containing the digestion reagent and a catalyst. The tube is capped with a polypropylene, PTFE lined cap and heated in a block digester at 150C for 2 hours. The orange Hexavalent chromium is reduced to a greenish trivalent chromium. The analytical range for the spectrophotometric method is 5-150ppm (measured at 420nm).

The used COD Tubetests contain strong sulfuric acid and other chemicals, so reagents must be handled carefully. The contents of the pipe should be disposed of in accordance with the requirements of local authorities.
These test tubes are SGC certified. These tubes can only be used once, so they cannot be reused.

To use the digital heater for the COD test, set the temperature on the digital display to 150°C. On no account must the heater be set at a higher temperature than that specified as this may cause a hazard through pressure build-up in the COD tubes.

Suitable for colorimeters and test kits on the market
Also suitable for instruments and test kits
Easy-to-open sealed vials eliminate the risk of cross-contamination
Extend the shelf life to five years
Used for municipal wastewater testing; industrial wastewater and process control testing; environmental water testing

Open COD test tube, hold it at an angle and slowly add
2.0 mL of the pretreated sample solution from the reaction tube without mixing so that two separate layers
are formed.
Screw cap securely on to test tube, hold tube by the cap, place tube into the safety bottle and shake
(Caution, test tube becomes hot). Place tube into the heating block. Start heating programme.
After 2 h remove test tube from heating block, allow to cool down to room temperature and shake gently
several times.
Clean outside of test tube and measure.
Adjust photometer to zero by using blank value “NULL”

Chemical oxygen demand is a vital test for assessing the quality of effluents and waste waters prior to discharge. The Chemical Oxygen Demand (COD) test predicts the oxygen requirement of the effluent and is used for monitoring and control of discharges, and for assessing treatment plant performance. The impact of an effluent or waste water discharge on the receiving water is predicted by its oxygen demand. This is because the removal of oxygen from the natural water reduces its ability to sustain aquatic life. The COD test is therefore performed as routine in laboratories of water utilities and industrial companies.

With the Aijiren COD tube test, each user can easily perform highly sensitive and accurate water detection.
The time required for the measurement process is significantly shortened, especially for standard analysis and series measurement, while significantly reducing the workload.
The COD Test tube contains a precise dose of reagent. Therefore, excessive chemical inventory is avoided and work safety is improved.

The Chemical Oxygen Demand (COD) test is widely used as a measure of organic contamination by determining the quantity of oxygen required for oxidation of reduced species including organic matter, in a water sample using a specific oxidizing agent, temperature and time reduction. COD testing is a good better indicator of organic pollutants in industrial wastewater containing cyanides and heavy metals. COD testing affords rapid response to changing conditions before critical problems develop. Lovibond’s COD vials are compatible with BOTH Lovibond and Hach® colorimeters.

Testing water for Total Organic Carbon (TOC) is no longer exclusive to the environmental industry. With the latest USP methods, TOC is now a concern for any industry using Purified Water and Water for Injection. Aijiren Low Level TOC Vials are specially cleaned and packaged to reduce TOC to the lowest levels possible, assuring a low background for your testing.

TOC is the abbreviate by Total Organic Carbon. The TOC Direct Method from Aijiren provides a reliable and practical means for water treatment facilities to frequently measure organic carbon to optimize treatment processes. Instead of purchasing an expensive, traditional TOC analyzer or outsourcing TOC determinations to a contract laboratory, this method can provide TOC results — accurately and inexpensively — right at your facility, and without any hazardous waste.