9mm Autosampler Vial for HPLC

The transparent glass threaded sample bottle is 2mL, 12x32mm, and has an advanced sample bottle sealing system. The screw vial can prevent the septum from being pressed in, and can provide a stop point for the bottle cap to prevent over-tightening or over-tightening, and it can provide the best and consistent seal every time.

Teflon and silicone rubber or ultra-pure silicone are used as raw materials to ensure that the septa are non-toxic; to ensure excellent functions, it is particularly suitable for gas chromatography, and to ensure that the septum does not fall into the sample vial during the injection process

The non-pre-slit septas help to reduce carryover from vial to vial because the resealing characteristics of the septum act as a squeegee to wipe solution from the outside of the needle. Typically, a non-slit septum exhibits resealing capabilities for a limited number of needle punctures but for long-term storage in the vial, using a new non-punctured septum is best practice.

HPLC autosampler vials  are generally categorized by vial diameter, vial height, and thread finish. Clear glass and amber glass have similar inert properties. Amber glass is used to protect sensitive samples from UV light. Markings on the vials provide sample identification information.

The Screw Caps that are inlcuded with this kit are knurled on the sides for excellent gripping and comfort when applyting to the vial. The silicone rubber / PTFE septa used were designed to provide the right amount of resistance to autosampler needles during the injection process so that they penetrate the vial properly without damaging the septa or the injection needle. Too much or too little resistance to the needles can damage the septa, compromise resealing, cause needle blockage from coring of the septa material and even damage your autosampler. These septa perform even when using a wide range of needles: fine, blunt or even dull. Low sample or solvent evaporation performance even after multiple injections have been observed when using aijiren caps.

2mL Amber Glass Screw Top Autosampler Vials are available in a variety of neck finishes and opening diameters. Large mouth or wide ID vials have approximately a 40% wider mouth opening than standard opening vials. The large opening reduces the risk of bent autosampler needles during sampling. When choosing a 2mL Amber Glass Screw Top Autosampler Vials, the product material is of paramount importance.

9mm thread screw neck vial, 32×11.6mm, transparent / amber PP, with graduation line, slightly concave shaped bottom
Preassembled cap and septafor 9mm thread screw PP cap, blue, centrel hole, PTFE/Silicone 9x1mm

Aijiren screw thread top sample vials design is characterized by universal ease of use, especially the use of automated sample introduction systems, so this type of vial is also called a autosampler vial. And this sample vial is extremely compatible. The 1.5ml sample vial we usually say is the 2ml volume sample vial. The design of Aijiren screw thread top vials are developed from Europe and the United States, and the design feature is easy to use, especially the use of automated sample introduction system. Aijiren screw thread top vials also known as autosampler bottles.

Glass Screw Vials ND9mm for HPLC, Clear & Amber, with /without Patch
High Recovery Glass Screw Vials ND9mm, Clear & Amber, with /without Patch
0.3ml Glass Screw Vial integrated with Micro-insert, Base Bonded, Clear & Amber, with /without Patch
PP Screw Vials ND9mm, Clear & Amber
0.3ml PP short Screw Micro Vials, Clear & Amber

The 9mm screw cap is made from high-quality material, providing excellent durability and chemical resistance. Its precise threading allows for easy and efficient sealing, ensuring a reliable closure for HPLC vials. The septa, made of a specialized material, offers optimal inertness and compatibility with a wide range of samples, ensuring accurate and reproducible results in HPLC analysis.

9mm screw autosampler vial is widely used in laboratory chromatographyanalysis. Aijiren as one of largest chromatography consumable supplier, supplies 9mm screw HPLC vial in wholesale price. This 9mm screw vial package can reduce screw vial mouth touch to prevent contamination of sample. At the same time, the package box can be used as a vial rock, it is save the cost. Welcome to inquiry us about chromatography consumable.

2ml 9mm Screw Top Autosampler Vials are cleaned and packaged in a certified Class 10,000 clean room according to a designed process, developed to eliminate chromatographic errors associated with vials. For Chromatography vials, 2ml 9mm Screw Top Autosampler Vials is the most commonly vial in laboratories. 2ml 9mm Screw Top Autosampler Vials are more leak-tight and easy for the experimenter to operate.

Caps for screw thread vials are available with either an open hole for autosampler use and standard addition or with a solid top for sample storage. One piece polypropylene cap and membrane are also available. These pierceable screw thread caps are designed for one time use and reduce sample preparation time as there is no cap and seal to assemble.

High recovery vials offer precision vials made from low expansion borosilicate glass and designed with a unique interior bottom, solid glass vial of a Microliter-Vial with inner cone, allowing for maximum retrieval of contents by a syringe.  

With its 9mm screw thread design and capacity of 1.5mL, this vial makes for easy handling and integration into autosamplers. Ideal for applications requiring limited quantities. The vial comes equipped with various finishes and closure options, such as screw caps and snap caps, so researchers can select their ideal choice according to their unique research needs.

Screw thread closures?N9?(9mm)?2ml vials and closures?are?universally suitable?on most autosamplers,?convenient?in handling and available in a broad?selection of different cap colors and septum materials. They?fulfill all requirements with regard to?tightness?and?analytical?purity?for GC as well as for HPLC. Due to the relatively thin?septa penetration is safe and easy.

Screw thread vials and caps provide low evaporation, reusability, less hand injury during manipulation than crimp seals and require no special tools. All screw threads vials and caps are differentiated by their thread finish as defined by the Glass Packaging Institute, GPI. For screw thread vials, a two part number is assigned. For example, 8-425 neck finish represents a vial with a diameter of 8 mm across the outside of the threads and a thread style of 425. Screw thread vials and caps are more expensive than crimp seals.

Screw cap vials are universal. When screwing on the cap, a mechanical force is applied that compresses the septum between the rim of the vial and the cap. Screw closures provide an excellent seal and mechanically hold the septum in place during piercing. No tools are required for assembly.

Suit for: 9mm Short Thread Vials
Caps Material: polypropylene
Cap Diameter: 9mm
Cap Features: 6mm Centre Hole or Closed Top
Septa Material: PTFE / Silicone
Septa Feature: Pre-slit I or X
Septa diameter: 9mm
Septa Thickness: 1mm

Amber Borosilicate Glass
ND9mm Screw Neck Vial
11.6*32mm
With Writing Spot
9mm Blue Short Screw PP Cap
with 6mm Centre Hole
Pre-slit / non-slit PTFE Silicone Septa
Septa Size: 9*1mm

The Autosampler Vial produced by Aijiren is often used in autosamplers. Whether it is Aijiren or other brands of autosamplers, Aijiren Autosampler Vial can be perfectly adapted. It is precisely because of this that Aijiren Autosampler Vial can be so well-known and become A well-known manufacturer of chromatography consumables in the world.

These vials are a good choice for the latest autosamplers. With an emphasis on improving sample security and integrity, we offer innovative 9mm closures and 9mm screw top vials for consistent productivity across all separations.
Standard opening screwed viars are manufactured from borosicate glass and the maximum filling volume is 2 ml.

Chromatography autosampler vials are widely used in chromatography, chemistry, medical and other fields. Autosampler vials are generally made of hydrolytic glass or borosilicate, with various specifications. Different vial mouth designs meet different actual needs.